Hunter fan light kit problems

Lighting on a ceiling fan operates similarly to any other type of light fixture. The only difference is that the wiring for the light routes through the ceiling fan and connects to the main wiring with the wiring from the fan. A pull switch is mounted on the base of the fan to control the function of the light. A nonfunctioning light indicates one of very few potential issues. Before tearing apart a good ceiling fan, examine the basics.

While uncommon, all the bulbs burning out at once can occur. Swap out one of the bulbs for a functioning bulb, and test it. Inspect the circuit breaker to see if that was tripped. Many people operate a ceiling fan from the pull switches without examining the wall switch. A seemingly unassigned wall switch may simply be a control switch for the ceiling fan. Looking at the basics will usually result in fixing a majority of problems. Inspect the pull switch.

A pull switch should be tight and click when pulled. Compare the pull switch for the lights to the pull switch for the fan blades. Pull the cover off of the fan, typically screwed into the base between multiple lights or mounted into the light fixture, to visually inspect the pull switch.

A damaged switch will have chunks of plastic in the switch, signs of scorching or damaged wires. Switches screw into the side through a screw-on cap on the outside of the switch.

The pull chain routes through the retaining cap.

hunter fan light kit problems

Unscrew the cap, and disconnect the electrical wires to replace the switch. The wiring for the light is usually not the cause of a nonfunctioning light.

Hunter Fan Recalls Brunswick Three and Four Light Ceiling Fans Due to Shock Hazard

If the fan works, the lights should work. Inspecting the wiring requires disconnecting the retaining screws that connect the fan to the mounting bracket in the ceiling and lowering the fan a few inches.

You should see blue and black wires from the fan twisted onto the black wire from the main wiring. The colors of the fan wires may vary, so consult your installation manual to identify the proper colors.

hunter fan light kit problems

Pull the cover off of the light fixture to inspect the wiring near the switch and light sockets. Damaged wires will have melted sheathings or scorch marks. Installing the ceiling fan with a light requires wiring the light to the main wiring.

If you just installed the ceiling fan and the light does not work, the wires were not connected properly. Consult the installation guide and correct the issue. When the light goes out post-installation and you have verified the function of the bulbs, the pull switch and the wiring, the only possible cause is the actual light socket.

Rarely does the light socket malfunction, but it is the only aspect not previously addressed.Skill Level: Beginner to Intermediate. This electrical project is best performed by a Licensed Electrician. Estimated Time: Depends on personal level experience, ability to work on a ladder and access to the light fixture. Precaution: Identify the light switch and turn it OFFthen wait for the bulbs to cool before exchanging light bulbs. Notice: Changes in light bulb type must not produce more heat which could damage light fixture components or the ceiling fan.

Ceiling Fan Wiring. Light Switch Wiring. Electrical Troubleshooting Troubleshooting Electrical Wiring.

The Non-Contact Electrical Tester This is a testing tool that I have had in my personal electrical tool pouch for years, and is the first test tool I grab to help identify electrical wiring. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use. This popular tester is also used by most inspectors to test for power and check the polarity of circuit wiring.

It detects probable improper wiring conditions in standard VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect Very handy and easy to use. The Wire Stripper and Wire Cutter My absolute favorite wire stripping tool that I have had in my personal electrical tool pouch for years, and this is the tool I use to safely strip electrical wires.

This handy tool has multiple uses: The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation. The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets. The wire stripper will work on both solid and stranded wire.

This tool is Very Handy and Easy to Use.

Hi Vicki, Make sure you are using the correct light bulbs as specified in the ceiling fan owners manual, and they are securely installed in the sockets. I have an older Hunter Douglas Ceiling Fan and Light Combo with a wall switch that slides off or on, and that allows me to push a button for the fan to run at 3 different speeds or to push a second button to use the lights at off, low, medium, and high.

Recently if the fan is running and the light is off, the light will spontaneously come on and stay on. I can turn the light off and a couple hours later the light will come back on. What could be the problem? Hi Carolyn, From what you have described the Wall Switch may be faulty, or if the switch is part of a Remote Control Unit then the fault may be with the Receiver Module located in the ceiling fan. A qualified electrician can inspect and test these components and replace the faulty unit as needed.

I hope this helps, Dave. My ceiling fan lights blink fast off and on when I turn it on. The ceiling fan is over 5 years old and has small round head light bulbs. Hi Shirley, Make sure the size of the light bulbs are the same as the original bulbs, or as specified by the ceiling fan documentation.

If the light bulbs watt size is larger then the lights may flicker on and off. Flickering lights may also be an indication of a faulty wall switch or the pull chain light switch on the ceiling fan. I replaced an old ceiling fan. After the installation the light will blink on but go off immediately after I turn the fan on at the wall switch. There is not a separate switch for the light.

I have a remote as the fan is 14 feet high. The light comes on normally when I use the remote to turn on the light. It only blinks when I turn it on at the wall switch. My electrician told me to call the fan company, not helpful after being paid.

Hi Judy, From what you have described it could be that the neutral wire is wired thru the wall switch instead of the power wire, or the wiring connections to the remote module may be reversed from the power source. The only way to know for sure would be to check the circuit wires with a voltage tester.Here at Hunter, we make high-quality fans to fit stylish spaces. Standing behind every fan we make it our mission to help you with installation, manuals, ceiling fan parts, accessories, and any product-related questions.

Find basic information, manuals, and replacement parts for all of our modern, traditional, vintage-inspired, and specialty low profile and flush mount fans. We can even help you find in-person repair specialists and professionals to install fans and their accessories.

Whether you choose to install your fan on your own or have a contractor or electrician take care of it for you, all of our ceiling fans come with a manual that includes installation information.

How To Remove Wattage Limiters From New Ceiling Fans

However, we understand that those manuals can easily get lost in the shuffle or accidentally thrown away. If this happens, simply use our online ceiling fan manual and parts finder. Hunter fan parts like light kits, downrods, replacement shades, and even specialty bulbs can keep your fan running right. We aim to make it easy for our customers to find ceiling fan repair parts and replacement parts to get their fans up and running again.

Enter the model number, and our ceiling fan manual and parts finder shows you a list of available parts for your fan. Note that not all repair parts are available through Hunter. Some items like capacitors, wattage limiters, and switches cannot be purchased individually.

Ceiling Fan Not Working? Troubleshooting Guide

Instead, you'll want to use a complete wiring harness for your model to make repair fast, simple, and safe. Getting a copy of your Hunter fan manual through our website can help you with installation, adding accessories like light kids, and finding replacement parts for your fan. Our website is also a rich resource for information you won't find in your basic fan manual. Take a look at the Hunter support page to find buying guides when you need a new fan and online ordering information so you can track your shipment after ordering.

Installation for fans and downrods, as well as access to recommended professionals to help you with your fan, can also be accessed through this page. If you already have your fan installed, you'll still find helpful information through our support page.

You can also access warranty and repair information to learn more about our commitment to quality and customer support for every fan we sell. Get the most out of your Hunter ceiling fan with a working manual and access to all of the replacement and upgrade parts you need.

Our troubleshooting page can help you find answers to common questions, but don't hesitate to contact us through our support page if you need additional help with your Hunter ceiling fan or placing an order. Login Create Account. Close Menu. Close search. How to Find your Model Number. Continue shopping view Cart.By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

It only takes a minute to sign up. I have an issue with my ceiling fan light; the light is on, then eventually over time it starts flickering off and on, eventually over time shutting off. I'll switch the light off, and then switch it back on, but no light. After a little while, I can get the light back on. Eventually it will start flickering again and shutoff.

While it's off, I tested the fan, and it works. Seems to me this is a loose wire in the light kit? Or maybe we need to replace the light kit altogether? Any place there is a wire connection could affect it. Is it possible this is the same problem I'm having with my Hunter fan's lite. The watt governor to keep the watts below max seems to have failed. I have tried changing out the bulbs both in size and cfl but both still "disco" flash when the light is turned on at the switch.

No remote. Looking for a little more detailed wiring instructions. All the web site info says by-passing the Watt Governor will solve my problem. Just need some help on how to do that. There is another smaller box with a Red and White wire. I don't know what that is. This problem is happening since the government reg to have these stepdowns installed on lite kits. It requires ceiling fan light kits manufactured after January 1, to be designed such that they cannot operate over watts.

It applies to all manufacturers. How they achieve the limit is up to them. It's an energy conservation step, not a safety one. I can't imagine how that made sense to anyone, but it nevertheless is the the rule.

I just bypassed the watt governor in my Hunter fan light. I had the same problem with flickering lights which progressed to the light coming on for two seconds and then going out. To bypass the device, tie the white wire from the light to the bundle of white wires with the wire nut. Tie the black wire to the black and white wire from the square connector that mates with the connector from the fan.Due to the extraordinary circumstances surrounding COVID, some of the remedies identified in recall press releases may not be available at this time.

Consumers should check with recalling firms for further details. It is important to remember that CPSC and recalling firms urge consumers not to use recalled products. Hunter toll-free at from 8 a.

hunter fan light kit problems

CT Monday through Friday or online at www. This recall involves Hunter Brunswick ceiling fan models, The model number can be found on a label on top of the motor housing. The recalled ceiling fans have three or four lights. The fans have four blades and range from inches to inches in blade span. They were sold in the following colors: white motor housing with white blades on one side and gray oak blades on the other side; black natural iron motor housing with gray oak blades on one side and aged oak blades on the other side.

Consumers should immediately stop using the recalled ceiling fans and contact Hunter to receive a free replacement light kit. The U. CPSC is committed to protecting consumers and families from products that pose a fire, electrical, chemical or mechanical hazard.

CPSC's work to help ensure the safety of consumer products - such as toys, cribs, power tools, cigarette lighters and household chemicals -— contributed to a decline in the rate of deaths and injuries associated with consumer products over the past 40 years. Federal law bars any person from selling products subject to a publicly-announced voluntary recall by a manufacturer or a mandatory recall ordered by the Commission.

To report a dangerous product or a product-related injury go online to www. Consumers can obtain news release and recall information at www. The link you selected is for a destination outside of the Federal Government. CPSC does not control this external site or its privacy policy and cannot attest to the accuracy of the information it contains. You may wish to review the privacy policy of the external site as its information collection practices may differ from ours.

Linking to this external site does not constitute an endorsement of the site or the information it contains by CPSC or any of its employees. Skip to main content. Name of product:. The light kit wires can be damaged, posing an electric shock hazard to the consumer. Recall date:. Consumer Contact:. Recall Details Description:.This company is not yet accredited. See reviews below to learn more or submit your own review.

Thank you, you have successfully subscribed to our newsletter! Enjoy reading our tips and recommendations. A link has directed you to this review. Its location on this page may change next time you visit. My ceiling fan remote quit working.

hunter fan light kit problems

I have to turn on the light at the wall and the fan does run on the last speed it was on when quit working. Bought a new battery and did a repair. No go. I called the company and my options are either buy a new remote or sensor in the fan. What a piece of junk. I will never buy another Hunter Product again and will share my experience with this less than professional company. New house in with 11 new Hunter Fans, to date 3 have had to be repaired.

We have no receipt because builder installed all and therefore have NO warranty. The old house had 5 Hunter fans that were 28 years old and only had to replace light bulbs, Now that's quality. The new fans are junk. Don't just take my word for it. Read all the reviews. I am not alone. Get buying tips about Appliances delivered to your inbox. Hunter Fans does not reimburse clients for out of pocket expenses, due to a defective product, that I experienced with a fan less than 6 months old.

One of the blades on the fan snapped where it was bolted on. I asked them to pay for my electrician having to make extra trips to fix their product. Could not locate a supervisor when I asked to speak with one about this issue. They used to be a good company. Very disappointed. I purchased 3 of the Masterson Hunter ceiling fans when I built the house 3 years ago. All 3 have quit working now.

I have bought hunter ceiling fans for every house we have ever owned. Never been so disappointed in a product period. I have replaced all 3 fans with a different manufacturer and will never buy another hunter ceiling fan period. I guess I'm lucky it didn't burn down the house.

Do not buy a hunter product. For more information about reviews on ConsumerAffairs. Bought out Hunter Ceiling fan from Lowes inthe light stopped working when we replaced a light bulb.

Never had a problem prior.At the time I was way too busy to fix it and tried calling my electrician. Turns out he was knee deep in work, which is often the case in July. Broken pull chains and ceiling fan repairs, while rare, can still be a costly project if you have to pay someone else.

Turn the power off to the ceiling fan before you do anything. Do this at the electrical panel or fuse box. The shades will have 3 to 4 set screws. Simply turn them counterclockwise with one hand while holding the shade.

In my case there were 2 screws that needed to be completely removed and 1 slotted screw that only had to be loosened. Again, take a picture of the wiring then undo the two wire nuts that wire it to the rest of the light kit.

This was a small project that saved me a ton of money. Learning how to patch drywall can also be a great cost savings! Send Me The Guide. Hi Jeff. The vinyl flooring next to my bathtub needs recaulked but has lifted slightly. If you have any suggestions, they would be greatly appreciated. Cut a strip of wood the length of the lifted section and place it on top of the floor. Then add weight to the wood to press down the floor while the adhesive sets. You could use sand bags, cinderblocks, or have two 10 year kids stand on it for 24 hours just kidding.

How about adding adhesive and then tacking all down with a piece of plastic quarter round or similar. You can paint the plastic, too. Thanks Jeff, great instructions! Now, what about the fan part? Ours is not working! Just buy a new one? Our son at the present time is removing tile from a small shower! I told him about you web site.

How to Troubleshoot a Hunter Ceiling Fan

I am sure he will sign up. How do I fix my sink stopper so it will stay open. I am using my fingers now. Thanks, Mary Croix. By the fan part, are you speaking about the other pull chain Mary? If so, you could call and see if that part is available instead of replacing the entire fan. Then you can slide the rod into the slot of the stopper. What kind of stopper is it? The kind that you pull up on it or push it in to stop up water.

If it is the the one you pull up on the small rod that sits on the back of the faucet then you have to go under the sink. There should be a little lever that screws in on the side of the pipe connected to the drain. If the is not one then you need to get on that does other wise a plug is not part of the drain.

If there is a small rod lever attacjed to the side of the pipe then you have to unscrew it.


thoughts on “Hunter fan light kit problems

Leave a Reply

Your email address will not be published. Required fields are marked *